does a vpn use a lot of data does a vpn use a lot of mobile data does using a vpn use more data

Does a VPN use a lot of data? Where the extra bytes go

Adrian Maverick · · 7 min read

No, a VPN does not use a lot of data. It adds a small wrapper to every packet you send and receive, plus a few tiny messages to keep the connection alive, so the same browsing uses slightly more data than it would without the VPN.

The streaming, downloads and app updates you do through the VPN are what fill your data plan. Here is where the extra bytes come from, how big they are, and how to check your own numbers.

Where a VPN's extra data comes from

A VPN takes each packet your device would normally send, encrypts it, and puts it inside a new packet addressed to the VPN server. That new packet needs its own addressing and its own security fields. Those extra bytes are the overhead.

There are three sources:

  1. The wrapper on every packet. New headers plus an authentication tag.
  2. Padding. Some protocols round the encrypted packet up to a fixed block size.
  3. Upkeep messages. Handshakes to refresh encryption keys, and in some cases keepalive packets.

The VPN does not download anything extra on your behalf. Your apps fetch the same pages and videos either way.

How big the wrapper is

WireGuard is a good protocol to look at because its author has published the exact numbers. In a post on the WireGuard mailing list, Jason Donenfeld broke the overhead down like this:

Part of the wrapper Size
Outer IP header 20 bytes (IPv4) or 40 bytes (IPv6)
UDP header 8 bytes
WireGuard type, key index and counter 16 bytes
Authentication tag 16 bytes
Total 60 bytes (IPv4) or 80 bytes (IPv6)

The header sizes come from the internet's own standards. RFC 791 sets the smallest IPv4 header at five 32-bit words, which is 20 bytes. RFC 768 defines the 8-byte UDP header. RFC 8200 defines IPv6. The WireGuard fields are listed on its protocol page, and its whitepaper says there are exactly 16 bytes of header fields before the encrypted data.

Donenfeld's worked example uses a standard 1,500-byte packet. With the IPv6 wrapper, 1,420 bytes are left for your data. Do the arithmetic and 80 bytes out of 1,500 is a little over 5 percent of a full-size packet, and 60 bytes is 4 percent. That is the cost on the big packets that make up a download or a video stream.

Other VPN protocols wrap packets differently and spend a different number of bytes. WireGuard is known for a lean format, and our WireGuard vs OpenVPN post goes into how the two differ.

Why small packets cost more

The wrapper is a fixed size. On a 1,500-byte packet it is a small share. On a tiny packet, such as the short acknowledgments your device sends back while it downloads, the same 60 or 80 bytes can be as big as the packet itself.

Padding adds a little more. WireGuard's protocol page says each packet is zero padded "to make the length a multiple of 16" before it is encrypted, and the whitepaper explains that this is done "to complicate traffic analysis." The padding is never allowed to push a packet past the maximum size, so it matters on small packets and not on full ones.

This is why no honest single percentage exists for "how much data a VPN uses." Traffic made of big packets, like video, sees the low end. Traffic made of lots of small packets, like messaging or a voice call, sees a higher share, but those activities use very little data to begin with.

The upkeep traffic

A VPN also sends a few packets of its own. With WireGuard these are small and infrequent:

  • Key refresh. The protocol page says a short handshake "occurs every few minutes" to rotate keys. The whitepaper sets this at about every 120 seconds while you are sending data.
  • Passive keepalive. If your device receives data but has nothing to send back for 10 seconds, it sends an empty packet so the server knows the link is alive. The whitepaper says this only happens while the other side is sending data.
  • Persistent keepalive. An optional setting that sends a packet at a fixed interval to keep routers and firewalls from closing the connection. WireGuard's quickstart says it is off by default, suggests 25 seconds when needed, and says it "makes WireGuard slightly more chatty."

When nothing is happening, WireGuard sends nothing. The quickstart calls it "not a chatty protocol." So a VPN left connected on an idle phone does not quietly eat your plan.

How to measure what your VPN uses

Your own numbers beat any estimate. Both phones show data use per app.

  1. Find the per-app screen. On iPhone, Apple's cellular data page says to go to Settings, Cellular, scroll down and tap Show All. On a Pixel, Google's mobile data page says to open Settings, Network & internet, SIMs, then App data usage.
  2. Note the starting numbers for the VPN app and the apps you plan to use.
  3. Use your phone normally for a day with the VPN on, then check again.
  4. Look at which apps grew. If a video app or a cloud backup grew by a lot, that is your data going somewhere, not the VPN's overhead.
  5. Compare with your carrier. Google notes that some carriers measure usage differently from the phone, and Apple says your carrier has the most accurate figure for your billing period.

If one app is the problem, the fix is in that app's settings, not in turning off the VPN.

Gotchas

  • Roaming. A VPN does not change what counts as roaming. Data through the tunnel is still roaming data, and the overhead is charged at roaming rates too. Apple's page says to turn off Data Roaming if you want to avoid roaming charges.
  • Data Saver can block the VPN. On a Pixel, Data Saver limits background data on mobile. If your VPN drops when Data Saver is on, add it under Unrestricted data.
  • A sudden jump is rarely the VPN. Backups, photo sync and app updates that run when you first set up a phone or reinstall apps can look like VPN data. Check the per-app list.
  • Speed is a separate question. The wrapper and the detour through the server can slow things a little. That is covered in does a VPN slow down your internet.

Frequently asked questions

Does a VPN use a lot of mobile data?

No. On mobile data the overhead is the same small wrapper and the same upkeep packets as on Wi-Fi. Our post on whether a VPN works on mobile data covers the rest of what changes on cellular.

Does a VPN use data on Wi-Fi?

It uses whatever connection you are on. On Wi-Fi the extra bytes go over Wi-Fi, so they only matter if your Wi-Fi itself has a cap, like a hotspot or an in-flight plan.

Does using a VPN use more data?

Slightly more. For WireGuard, the wrapper on a full-size packet works out to about 4 to 5 percent, more on small packets, plus a few small upkeep messages.

Does a VPN use data when I am not using the internet?

Very little. WireGuard stays silent when idle unless persistent keepalive is turned on, and even then it sends a tiny packet every so often.

Will a VPN drain my battery along with my data?

The extra data is small, and so is the extra power on a modern phone. See does a VPN drain battery for how to check the real cost.

Secria VPN

If you want a VPN that you can leave on without thinking about it, Secria VPN is post-quantum on every connection and runs on RAM-only servers. No activity logs: we do not record browsing, DNS queries or traffic contents. It is $7.99 a month, or part of Secria Pro at $9.99 a month with Secria Mail and the VPN on 5 devices. See pricing.

Secria fact-checks every post against primary sources. Spotted something wrong or out of date? Email hq@secria.me and we will correct it.